Australian houses and the trades that keep them standing

Weatherboard JournalWEATHERBOARD JOURNAL

Kitchens

The engineered stone ban and your kitchen

The benchtop that defined a generation of renovations can no longer be made, supplied or installed in Australia. The one already in your kitchen can stay, with conditions on who touches it.

A kitchen bench seen from the front with a stone top, sink and tiled splashback
A benchtop left alone is not the hazard. Cutting, grinding and drilling it is. Drawing: Weatherboard Journal.

For about twenty years the default Australian kitchen had a reconstituted stone benchtop: crushed quartz bound in resin, polished flat, sold under a dozen brand names and specified by nearly every builder of project homes. It was hard and consistent, and it photographed well. It was also hazardous to the people who cut it.

The Asbestos and Silica Safety and Eradication Agency states the reason in two sentences. Work with engineered stone can generate a great deal of silica dust and has been linked to increased rates of silica-related diseases. The crystalline silica content varies, but it can exceed 90 per cent, which is significantly greater than what is found in natural stone. Every sink cut-out and every edge trimmed on site put that dust into the air around a stonemason.

What is banned, and from when

The prohibition has two dates.

From 1 July 2024, there is a ban on the manufacture, supply, processing and installation of engineered stone benchtops, panels and slabs. The Department of Employment and Workplace Relations describes it as applying across Australia, implemented through each jurisdiction's work health and safety laws, and advises checking the arrangements with the regulator in your state or territory.

From 1 January 2025, importing engineered stone benchtops, panels and slabs is banned as well. The department explained the second measure as an extra layer of deterrence at the border, given that most engineered stone products were imported.

In practical terms, no fabricator can lawfully make you a new engineered stone benchtop, no supplier can sell you a slab, and no installer can fit one.

What is not banned

The exclusions matter to anyone choosing a replacement material.

  • Porcelain and sintered stone. The department says the ban does not apply to porcelain and sintered stone products, including benchtops, slabs and panels.
  • Natural stone. The agency confirms the prohibition does not apply to natural stone benchtops, panels or slabs, and gives a granite benchtop as its example.
  • Finished products. Engineered stone items that do not need to be processed or modified are excluded. The official examples are jewellery, garden ornaments, sculptures and kitchen sinks.

A material being lawful does not make it dust-free. Natural stone contains silica too, and work health and safety rules on crystalline silica apply to fabricators whatever they are cutting. That is the fabricator's obligation to manage. Your part is to choose one who cuts wet, in a workshop, and does as little as possible on site.

The benchtop you already own

The ban does not reach back into existing kitchens. Engineered stone installed before the prohibition is referred to in the rules as legacy engineered stone, and nothing requires you to remove it. The hazard the ban addresses is the dust made by working the material, not the slab sitting under your kettle.

The rules apply at the moment someone needs to work on it. The agency sets out the position: work involving the controlled processing of legacy engineered stone to repair it, remove it, make minor modifications to it or dispose of it is permitted, but the work health and safety regulator must be notified before the work is carried out. Processing means using a power tool or other mechanical plant to crush, cut, grind, trim, sand, abrasive polish or drill the stone. An engineered stone process also counts as high-risk crystalline silica work, with its own set of obligations for the business doing it.

Ordinary renovation jobs fall inside that definition more often than owners expect.

  • Enlarging a cut-out for a bigger cooktop or a new sink.
  • Drilling a hole for a filtered water tap or a soap dispenser.
  • Trimming a benchtop to fit a new appliance.
  • Cutting a top into pieces to get it out of the house.

Each of these is processing, each has to be done with dust controls by a business that has notified the regulator, and none is a job for a handyman with an angle grinder on the back lawn. Safe Work Australia publishes a flowchart for the notification step, linked from the agency's page.

There is one accommodation for renovators. The agency notes that in most jurisdictions an exemption allows the reinstallation of an engineered stone benchtop when other work is needed on the premises, with the example of a top that must be lifted to get at the cabinets underneath and then put back. It tells readers to check with the local regulator, because the detail differs between states.

Planning a kitchen renovation now

If you are keeping existing stone tops, design around them. Choose a sink and cooktop that fit the existing cut-outs, and put new tap holes in the sink deck where you can. Each alteration you avoid is a notification and a controlled cutting job you do not have to pay for.

If the tops are coming out, tell every builder who quotes that the benchtops are engineered stone, and ask how removal will be handled and by whom. The honest answer includes the words "notify" and "controlled". A demolition allowance that treats the kitchen as general waste has not priced the job.

If you are choosing new tops, the lawful options include porcelain, sintered stone, natural stone, timber, stainless steel, laminate and solid surface. Ask the fabricator where the cutting will be done. And if a supplier offers engineered stone slab from old stock at a discount, decline. Supply has been prohibited since 1 July 2024.

A last point for people who own a newer house. A benchtop described on the plans simply as "stone" could be either kind. If it was installed before mid-2024, is perfectly uniform in pattern and came with a project home, treat it as engineered stone until the builder's selections sheet or the fabricator tells you otherwise.

Questions readers ask

Do I have to replace my engineered stone benchtop?

No. The prohibition covers manufacture, supply, processing and installation. It does not require installed benchtops to be removed, and the rules for legacy stone only apply when someone works on it.

Can a tradesperson drill a tap hole in my existing benchtop?

Drilling is processing under the rules. Work to make a minor modification to legacy engineered stone is permitted if it is controlled, and the work health and safety regulator must be notified before it is carried out. Use a business that does this routinely, not a general handyman.

Sources

  1. Engineered stone prohibition, Asbestos and Silica Safety and Eradication Agency
  2. Prohibition on the use of engineered stone, Department of Employment and Workplace Relations